Peptide molecular weight calculator.

Paste a peptide sequence to get its molecular weight, monoisotopic mass, formula, isoelectric point (pI), net charge, GRAVY and amino-acid composition. It is free and runs in your browser.

One-letter codes, for example GHK. Spaces and line breaks are ignored.

End groups

Results

Results appear here after you calculate.

Vitrapep sells research peptides for laboratory research use only. Not for human or veterinary use.

How it's calculated

Average molecular weight
The sum of the average residue masses in the ExPASy mass table (SIB Swiss Institute of Bioinformatics), plus one water (18.01524 Da). These are the values ExPASy ProtParam uses.
Monoisotopic mass
Calculated from the molecular formula with the exact masses of 12C, 1H, 14N, 16O and 32S from NIST.
Molecular formula
The sum of the residue formulas plus H2O, written in Hill order: C, then H, then the other elements.
End groups
An N-terminal acetyl adds C2H2O (42.0373 Da average, 42.0106 Da monoisotopic). A C-terminal amide swaps OH for NH2 (−0.9847 Da average, −0.9840 Da monoisotopic). Each one removes a charged end from the pI and charge estimate. Values from the same ExPASy table.
Isoelectric point and charge
Net charge comes from the Henderson-Hasselbalch equation with the EMBOSS iep pKa set below. The pI is the pH where the net charge is zero, found by bisection between pH 0 and 14. Estimates differ between pKa sets (Kozlowski, 2016).
EMBOSS pKa values
GrouppKa
N-terminus8.6
C-terminus3.6
Asp (D)3.9
Glu (E)4.1
Cys (C)8.5
Tyr (Y)10.1
His (H)6.5
Lys (K)10.8
Arg (R)12.5
GRAVY
The mean of the Kyte-Doolittle hydropathy values over all residues (Kyte and Doolittle, 1982).
Residue counts
Acidic: D, E. Basic: K, R, H. Hydrophobic: A, V, I, L, M, F, W.
Example
The Example button loads the published 15-residue sequence of BPC-157, GEPPPGKPADDAGLV (PubChem CID 9941957).
Not included
Disulfide bonds, cyclization, other modifications, salt forms and non-standard residues.

How do you calculate a peptide's molecular weight?

Add the mass of every amino-acid residue in the chain, then add one water (18.015 Da) for the free amino and carboxyl ends. A residue mass is the amino acid's mass minus the water lost when a peptide bond forms. For GHK that is 57.0519 + 137.1411 + 128.1741 + 18.0152 = 340.38 Da, with the formula C14H24N6O4. The monoisotopic mass (340.1859 Da) uses only the most common isotope of each element, and high-resolution mass spectrometry usually reports that value for small peptides.

Sources: ExPASy residue masses, NIST isotopic compositions, PubChem CID 73587 (GHK). More in our guide to peptide molecular weight.

What is a peptide's isoelectric point?

The isoelectric point (pI) is the pH at which a peptide carries no net electric charge. It depends on the free amino and carboxyl ends and on the side chains of Asp, Glu, Cys, Tyr, His, Lys and Arg. The calculator adds up the charge of each group with the Henderson-Hasselbalch equation and searches for the pH where the total is zero. Published pKa sets differ, so two tools can give pI values a few tenths apart for the same sequence.

Sources: EMBOSS iep documentation, Kozlowski LP. IPC: Isoelectric Point Calculator. Biology Direct. 2016;11:55.

Why does the MW on a certificate differ slightly?

Tools use slightly different atomic-weight tables and rounding, which can move the average weight by a few hundredths of a dalton. A certificate may also list the monoisotopic mass or an observed ion such as [M+H]+, which is about 1.007 Da above the neutral mass. Each disulfide bond lowers the mass by 2.016 Da, and end groups such as an amide or acetyl change it too. Some documents give the weight of a salt form, such as an acetate or TFA salt, which is higher than the free peptide.

Sources: IUPAC CIAAW standard atomic weights, ExPASy mass values. See also how to read a certificate of analysis and peptide purity and HPLC.

What is GRAVY?

GRAVY stands for grand average of hydropathy. Each amino acid has a Kyte-Doolittle hydropathy value, from 4.5 for isoleucine to −4.5 for arginine, and GRAVY is the average of those values over the sequence. A positive score means the sequence is hydrophobic overall, and a negative score means it is hydrophilic overall. It ignores 3D structure, so treat it as a rough index.

Source: Kyte J, Doolittle RF. A simple method for displaying the hydropathic character of a protein. J Mol Biol. 1982;157(1):105-132.

Calculator FAQ

Is this peptide calculator free?

Yes. It is free to use, with no account or sign-up. It works on phones and computers.

Is my sequence sent or saved anywhere?

No. The calculation runs in your browser. Your sequence is not sent to our servers or saved.

Which letters can I enter?

The 20 standard one-letter codes: ACDEFGHIKLMNPQRSTVWY. Lowercase, spaces, line breaks and a FASTA header line are fine. You can type Ac- at the start or -NH2 at the end to set the end groups. Ambiguous codes such as B, Z and X are not accepted, because their mass is not fixed.

Does it account for disulfide bonds or other modifications?

It handles an N-terminal acetyl group and a C-terminal amide. It does not model disulfide bonds, cyclization, phosphorylation or non-standard residues. For each disulfide bond, take two H off the formula, 2.016 Da off the average weight and 2.0157 Da off the monoisotopic mass.

Which pKa values does it use?

The EMBOSS set: N-terminus 8.6, C-terminus 3.6, Asp 3.9, Glu 4.1, Cys 8.5, Tyr 10.1, His 6.5, Lys 10.8 and Arg 12.5. ExPASy ProtParam uses a different set (Bjellqvist), so its pI can differ. For BPC-157, ProtParam gives 4.03 and this calculator gives 3.88.